Tribological Properties of Nitrate Graphite Foils

• Published in: Nanomaterials (Basel, Switzerland) Vol. 14; no. 18; p. 1499
• Main Authors: Morozov, Nikolai S, Demchenko, David V, Bukovsky, Pavel O, Yakovenko, Anastasiya A, Shulyak, Vladimir A, Gracheva, Alexandra V, Chebotarev, Sergei N, Goryacheva, Irina G, Avdeev, Viktor V
• Format: Journal Article
• Language: English
• Published: Switzerland MDPI AG 15.09.2024; MDPI
• Subjects: Analysis; Anisotropy; Coefficient of friction; Coherent scattering; Cold rolling; Composite materials; Deformation; Deformation analysis; Deformation effects; Density; Foils; Fractions; Friction; Graphite; graphite foil; Industrial plant emissions; Mechanical properties; Misalignment; Modulus of elasticity; Particle size; Plastic deformation; Rolling direction; roughness; Static friction; Strain; Stress concentration; stress–strain state; structure; Surface roughness; Tribology; coefficient of friction; graphite foil; stress–strain state; roughness; microstrains; mechanical properties; structure; residual macrostresses
• ISSN: 2079-4991; 2079-4991
• DOI: 10.3390/nano14181499

This study investigates the tribological properties of graphite foils (GF) with densities of 1.0, 1.3, and 1.6 g/cm , produced from purified natural graphite of different particle sizes (40-80 μm, 160-200 μm, >500 μm). Surface roughness was measured after cold rolling and friction testing at static (0.001 mm/s) and dynamic conditions (0.1 Hz and 1 Hz). Results showed that static friction tests yielded similar roughness values ( ≈ 0.5-0.7 μm, ≈ 0.5-1.0 μm) across all densities and particle sizes. Dynamic friction tests revealed increased roughness ( from 0.7 to 3.5 μm, from 1.0 to 6.0-7.0 μm). Friction coefficients (µ) decreased with higher sliding speeds, ranging from 0.22 to 0.13. GF with 40-80 μm particles had the lowest friction coefficient (µ = 0.13-0.15), while 160-200 μm particles had the highest (µ = 0.15-0.22). Density changes had minimal impact on friction for the 40-80 μm fraction but reduced friction for the 160-200 μm fraction. Young's modulus increased with density and decreased with particle size, showing values from 127-274 MPa for 40-80 μm, 104-212 MPa for 160-200 μm, and 82-184 MPa for >500 μm. The stress-strain state in the graphite foil samples was simulated under normal and tangential loads. This makes it possible to investigate the effect of the anisotropy of the material on the stress concentration inside the sample, as well as to estimate the elasticity modulus under normal compression. Structural analyses indicated greater plastic deformation in GF with 40-80 μm particles, reducing coherent-scattering region size from 28 nm to 24 nm. GF samples from 160-200 μm and >500 μm fractions showed similar changes, expanding with density increase from 18 nm to 22 nm. Misorientation angles of GF nanocrystallites decreased from 30° to 27° along the rolling direction (RD). The coherent scattering regions of GF with 40-80 μm particles increased, but no significant changes in the coherent scattering regions were observed for the 160-200 μm and >500 μm fractions during dynamic friction tests. Microstrains and residual macrostresses in GF increased with density for all fractions, expanding under higher friction-induced loads. Higher values of both stresses indicate a higher level of accumulated deformation, which appears to be an additional factor affecting the samples during friction testing. This is reflected in the correlation of the results with the roughness and friction coefficient data of the tested samples.